Nah dibawah ini ada beberapa macam kode eror pada Printer Epson 9880, selamat menyimak!
Epson 9880 Error Codes:
0002 – Carriage Motor / Ink Tube is near end of life (Clear Carriage Motor Counter)
0004 – Nozzle check error
0008 – RTC error (Real Time Clock) (Check the Battery and reset the Date and Time)
0020 – Print Head life counter (Reset the Head counter)
0040 – Cleaning Unit near end of life (Reset When Cleaning Unit Change)(Pump Assy, Pump Motor, Cap Assy, Wiper Blade, Flushing Box).
0080 – Date is not set (Set the date and time (RTC))
0100 – RTC Battery low (Replace the battery, and reset the RTC)
0400 – Pressure Pump Assembly near end of life (Reset When Pump Unit Change) Inspect and replace if necessary.
00000088 – RTC (Real Time Clock) data is corrupted
00000101 – Carriage Motor life (Reset When CR Unit Change), check for leaky ink tubes)
00000103 – RTC (Real Time Clock) battery is defective
00000105 – Print Head end of life (Inspect print head and reset head counter)
00010000 – Paper Feed Motor encoder check error (Check Sensor and Timing Disk)
00010001 – Paper Feed Motor out of step
00010002 – Paper Feed Motor overcurrent (Check for mechanical binding of the feed rollers / motor)
00010003 – Paper Feed Motor in-position time-out
00010004 – Carriage Motor encoder check error (Check sensor and Timing Disk)
00010005 – Carriage Motor out of step
00010006 – Carriage Motor overcurrent (Check for mechanical binding, If not replace motor)
00010007 – Carriage Motor in-position time-out
00010008 – Servo interrupt watchdog time-out
00010009 – System interrupt watchdog time-out
0001000A – Carriage home position error (Check Sensor and mechanical components)
0001000C – Platen Gap home position error (Check Sensor and mechanical components)
0001000F – Carriage Motor PWM output faulty
00010010 – Paper Feed Motor PWM output faulty
00010014 – Ink System Pressurization Error (The Pressure Sensor does not indicate pressure)
0001001B – Head driver (TG) temperature error
0001001D – Carriage servo parameter error
0001001E – Paper feed servo parameter error
00010020 – CSIC read / write error
00010023 – RTC (Real TIme Clock) (Reset RTC)
00010025 – CSIC ROM communication error
00010026 – RTC (Real TIme Clock) communication error
00010027 – Pressure Pump Micro Leak Error (only displayed when testing in Service Mode)
00010028 – Head error
00010029 – Unidentified NMI
0001002A – Carriage ASIC ECU error
0001002B – Paper feed ASIC ECU error
0001002D – Cleaning Unit end of life (Reset When Cleaning Unit Change)(Pump Assy, Pump Motor, Cap Assy, Wiper Blade, Flushing Box).
0001002F – 360 DPI writing time out error
00010035 – Pump Home Position Error (Check Sensor and mechanical components)
00010036 – Type B Interface board installation error (Type-B Card is Level 2 or below)
00010037 – Print Head thermistor error (Print Head, Head Cable)
00010038 – Head Driver thermistor Error (Replace Main Board)
0001003B – Carriage Lock / Cutter Error
0001003C – Carriage Lock / Cutter Error
0001003D – Carriage Lock / Cutter Error
0001003E – Pressure Sensor Error (Sensor detects pressure before the pressure is generated)
0001003F – Pressure Pump Assembly end of life (Reset When Pump Unit Change) Inspect and replace if necessary.
00010040 – Printing Position Error (Caused by CR Encoder or Timing Strip)
00020000 – NVRAM error
00020002 – SDRAM error
00020003 – BOOT program SUM error
00020009 – Flash memory SUM error
0002000A – Program load error
0002000B – Internal memory shortage error
0002000C – Review error
100000E0 – CPU address error (load misalignment)
10000100 – CPU address error (storage misalignment)
10000180 – CPU reserve command code exception error
100001A0 – CPU slot illegal command exception error
100001C0 – AC disruption (AC Power) (Unplug and wait 30 sec., then plug back in) Bad Power)
100005C0 – CPU DMA address error
0003xxxxx – CPU error
0Dxxxxxxx – CPU error
No comments:
Post a Comment